Loading…
The unit is standard with a 15" discharge auger, with a capacity of up to 5 tonne per minute with an optional 18" discharge auger available. The standard drive is setup for a 540 rev drive tractor with an option of 1000 rev drive or hydraulic drive if sufficient oil supply. The cleaning of this unit is simple, just pull the floor bar out from the back and the bin will clean out completely.
Single, Dual, Triple, Quad-View & Picture in Picture Functions Suitable for up to 4 Waterproof Cameras
SOME INTERESTING INFORMATION ON INCREASED EFFICENCY BY OWNING A CHASER BIN
Stripping crops in the most efficient and time effective way is one of the main goals at harvest.
Some basic calculations reveal that stopping a harvester to unload the grain bin can potentially reduce harvest efficiency by 35 percent; in effect meaning harvest takes 35% longer than it needs to.
A common way to negate the lost time to stop and empty is to run a chaser bin.
Consider a harvester with a work rate of 40 tonnes per hour, a grain bin that can hold 9.5t and the harvester spends five minutes out of the crop each time the bin needs to be emptied. This means the harvester is spending 35% of the time out of the crop.
In this example the true harvester work rate is therefore reduced by 35% because it is only in the crop for 65% of the time.
Multiplied by the value of the grain being harvested ($200/t) and the percentage reduction in value of that grain after it is weather damaged (40%), the potential loss is therefore $1123/hour.
Of course there are events that would damage the crop completely, such as hail or fire, making the reduction in value of that grain $100%. In this case the loss would be $2800 for each hour spent harvesting due to the inefficiency from stopping to empty. But typically, weather-damaged grain is downgraded in value by about 40%.
Therefore, running a chaser bin would enable an extra $1123 worth of grain to be harvested during each hour of harvester operation.
CHASER BIN FEATURES AND OPTIONS
| CHASSIS | Manufactured from Heavy Duragal Channel and RHS |
| BIN BODY | Manufactured from 1.5 mm Galvanised butt welded sheet steel |
| AXLES | Axles are New heavy duty 10 stud steering assembly with a 40 ton weight rating |
| TYRES | Recommended on New Tractor Tyres 30.5 x 32 16 ply with New rims other sizes and options available |
| PTO / HYD DRIVE PTO | Drive with slip clutch, 540 RPM drive standard or optional 1000 RPM Drive, Heavy Duty Gear box with 1” drive sprockets. Hydraulic drive also available (If sufficient oil supply) |
| TRACTOR | Recommend a minimum of 180 H/P on firm ground |
| DISCHARGE AUGER | Fitted with hydraulic raise & lower and folding chute. Standard with 15” Auger with a discharge rate up to 5 ton per minute. Optional 18” auger with a discharge rate greater than 6 ton per minute |
| DISCHARGE HEIGHT | Minimum 4.5m |
| BIN HEIGHT | 3.3m |
| FLOOR AUGER | 10” Flight. Removable full length slide out floor and trap door for easy cleaning. Hydraulic ram controlled shut off doors cover auger flight allowing bin to be unloaded at any speed |
| FOLDING CHUTE | Hydraulic ram controlled folding chute on end of discharge auger (pictured above) |
| LED WORK LIGHT | 1200 Lumen LED Work light mounted by the discharge spout (pictured above) |
| SIGNS & LIGHTS | Fitted with over size sign, revolving light and LED stop tail & turning lights (pictured above) |
| DROP SPOUT | Optional Drop Spout Tube or hose for filling sheep feeders, auger hoppers etc. |
| QUAD VIEW CAMERA | Optional 9” Quad view monitor with 3 Camera’s mounted on the Bin, one on the end of discharge chute, one inside the bin and one at the rear of the bin |
Did you know; without a chaser bin, it isn't uncommon for a harvester to spend up to 35% of its time in the paddock unloading
To contact Vennings about 46 M³ Approximately 33 Ton Galvanised Chaser Bin use Get a quote.
Reach valuable industrial buyers in minutes
Promote key products & content
Drive cost effective & measurable sales